makerfocus

Features: - 5V 1A power supply for greater driving force - 3.3V and 5V power interface - Support 3V-5V sensor module - Micro:bit all pins lead - 3.5mm audio connector - 5 gold fingers - Built-in buzzer (switch switching) - With LE-GO mounting holes...

Description:ElecFreaks Micro:bit Tinker Kit is a set of Micro:bit accessory that enables you to connect all kinds of modules easily without a group of messy breadboard wires.It can be used for classroom teaching. Students can use this kit to create or complete more projects...

Description:CAN-BUS is a common industrial bus because of its long travel distance, medium communication speed and high reliability. It is commonly found on modern machine tools and as an automotive diagnostic bus. This CAN-BUS Shield adopts MCP2515 CAN Bus controller with SPI interface and...

Product descriptionColor:BlackThird Helping Hand Soldering Station Welding Tool Aluminum alloy base with Six Flexible ArmsGeneral:The Third Hand quickens soldering, electronics, and DIY projects allowing you to finish your work faster than ever before! Our Third Hand makes positioning a breeze with flexible arms.Specification:Aluminum alloy...

Description:ESP8266,ESP-12FWIFI Development Board4M bytesThis is D1 mini, it is a mini WIFI board based on ESP-8266EX.11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wiresupported(except D0)1 analog input(3.3V max input)1 Micro USB connectionHow to get started in Arduino:Setup driver:1. Before you use miniD1 boards, you need...

Product descriptionFeatures:Two selectable differential input channels.On-chip active low noise PGA with selectable gain of 32, 64 and 128.On-chip power supply regulator for load-cell and ADC analog power supply.On-chip oscillator requiring no external component with optional external crystal.On-chip power-on-reset.Simple digital control and serial interface: pin-driven...

DIY Radio FM Receiver Kit - MakerFocus Digital Radio 76MHz-108MHz Adjustable Wireless Receiver Speaker 5V Power Supply Easy to Assemble for Soldering Learning and Family Education Adult Beginner Learning Materials This soldering DIY kit can help you learn basic electronic knowledge and circuit principles,...

Features: SMPSInput: 12V Typical output: 20W (5V/4A)Absolute output: 25W (5V/5A)3CM quiet cooling fanRemote control safe power (Require Driver)Button control safe power (Require Driver)Recommended to be stacked at the bottomCan stack with other stack boardIndependent of the mainboard hardware ( Safe power must develop by yourself)Raspberry...

Features: The packaging not only include nuts and screws of this case, complimentary nuts and screws for you to assemble your Pi. This case comes with a Cooling Fan on top for your over-clocking needs.This is a new version case, the acrylic board thinner...

Instructions Link:http://wiki.52pi.com/index.php/BAT_RTC%28English%29 Functions overview:RTC modules is used to save time, record the data, this module use farad capacitance, which is higher cost performance.it is the upgrade version of the RPI RTC module with farad capacitor.Product features：- DS3231 internal integration crystals circuit, less power consumption-...

Product DescriptionESP32 Arduino wireless stick lite is an IoT suite that fully supports the standard LoRaWAN protocol. (Exclusive) Supports the Arduino version of the ESP32 + LoRaWAN protocol routine provided by Heltec. This is a standard LoRaWAN protocol that can communicate with any gateway/base...

Specifications:Chipset: ESPRESSIF-ESP32-PCIO-D4 240MHz X tensa single-/dual-core 32-bit LX6 microprocessorFLASH: QSPI flash/SRAM, up to 4 x 16 MBSRAM: 520 kB SRAMKEY: Reset, IO32Display: 0.91 SSD1306Power indicator lamp: RedUSB to TTL: CP2104Camera: OV2640  2MegapixelSteering engine: Analog servoOn-board clock: 40MHz crystal oscillator Working voltage: 2.3V-3.6VWorking current: About 160mAWorking...

ESP32 LoRa Development Board    Description:WIFI Kit series is the new development cost-effective networking program of our company, the main chip using Lexin ESP32, Tensilica LX6 dual-core processor, clocked at 240MHz, computing power up to 600DMIPS, chip built-in 520 KB SRAM, 802.11 b /...

Description:ESP32 is already integrated with antenna and RF balun, power amplifier, low noise amplifiers, filters, and the power management module.The entire solution is the least amount of PCB area.This board is 2.4 GHz dual mode WiFi and bluetooth chips by tsmc 40nm low power...

What is it?This tiny ESP8266 development board is a small version of WiFi deauther projects. It comes installed with the latest ESP8266 Deauther software.With this software, you can perform different attacks to test WiFi networks.Please note that the ESP8266 does only support 2.4GHz. For...

What is it?Deauth detector could detect a Wi-Fi deauthentication attack. Also you can flash any program by yourself.If you do not know what is wifi deauthentication attack.You can have a look here: https://github.com/spacehuhn/esp8266_deautherAfter you know how it works you can also flash deauth program...

Specifications: Size:75*65*75mm Battery type:AAA*2 Power supply:3V Sensor:photoresistance Legs material:PVC Body material:Acrylic   Features: Photosensitive Movement The antennae of the robot's head can sense light. When the light hits the left or right antennae, the vibration motors installed on the left or right legs will...

 Fisheye Night-vision Camera   Description:The camera is equipped with photosensitive resistance, which enables the camera to automatically detect and recognize light to automatically switch between the night-vision and day-time shooting mode. Manual settings are not required, plug-in then it can be used. The advantage is...

Specifications:Pixel : 5 megapixelSensor : OV5647CMOS size : 1/4inchSensor best resolution : 1080p4 screw holes: used for attachment , connect 3.3V power outputFocal Length : 2.35Diagonal angle : 130 degreeDimension: 25mm x 24mm Feature:1. Fish eye wide angle lens2. Night vision camera3. 5 MP pixel4....

GT-U7 GPS Module   Description:GT-U7 main module GPS module using the original 7th generation chip, Software is compatible with NEO-6M.With a USB interface, you can directly use the phone data cable on the computer point of view positioning effect.USB directly connected to the computer,...