Makerfocus DSTIKE DEAUTHER WATCH SE
DSTIKE DEAUTHER WATCH SE
|Difference||Deauther Watch SE||Deauther Watch V3||Deauther Watch V4|
|3D Print Case||YES||YES||YES|
|Battery Life Indicate||NO||YES||YES|
WHAT IS IT?
Deauther watch SE has redesigned surface and circuit. RTC could work for several months after you turn off the watch. You can also flash deauth detector software because it has buzzer now.
Deauther Watch is still an ESP8266 development board, but you can wear it like a smartwatch.
It comes installed with the latest ESP8266 Deauther software. With this software, you can perform different attacks to test WiFi networks.
Please note that the ESP8266 does only support 2.4GHz.
You can also use it to develop your own software. It is simple to use, just like any other ESP8266 development board.
Deauther Attack: Disconnect 2.4G WiFi
Deauther Beacon: Create fake networks
Deauther Probe：Confuse wifi trackers
Packet Monitor：Display wifi traffic
GPIOs and Hardware info
Display: SH1106 1.3" OLED
Display SDA: GPIO 5
Display SCL/SCK: GPIO 4
WS2812b LED: GPIO 15
Button Up: GPIO 12
Button Down: GPIO 13
Button Select: GPIO 14
Buzzer: GPIO 0
Side Button: RST
What makes it special?
Double Arcylic Protection
Soft sillica gel strap
500 mA charging current
Indicate charging LED (RED will turn off when full)
Protection: short, overcharging, over discharging, temperature
This project is a proof of concept for testing and educational purposes. Neither the ESP8266, nor its SDK was meant or built for such purposes. Bugs can occur!
Use it only against your own networks and devices! Please check the legal regulations in your country before using it. We don't take any responsibility for what you do with this program.
Who am I: I am Deauther Watch SE, my surface and circuit has been redesigned, but I am still an ESP8266 development board, also you can wear me like a smartwatch
WiFi Test Tool: Installed with the latest ESP8266 Deauther software, Deauther Watch can perform different secure tests for your 2.4GHz WiFi networks
Newly Added Function: Compared to other version of Deauther Watch, WiFi Deauther Watch SE has added a buzzer, so you can flash deauth detector software now
Extension Board: You can also use WiFi Deauther to develop your own software. It is simple to use, just like any other ESP8266 development board
Working Time: Built-in 500mAh battery, working time up to 4 hours. Low standby current, long battery life, allows you to use Dstike Deauther for a long time without worrying about charging
Closes the connection of WiFi devices by sending deauthentication frames to access points and client devices you selected. This is only possible because a lot of devices don't use the 802.11w-2009 standard that offers a protection against this attack. Please only select one target! When you select multiple targets that run on different channels and start the attack, it will quickly switch between those channels and you have no chance to reconnect to the access point that hosts this web interface.
Beacon packets are used to advertise access points. By continuously sending beacon packets out, it will look like you created new WiFi networks. You can specify the network names under SSIDs.
Probe requests are sent by client devices to ask if a known network is nearby. Use this attack to confuse WiFi trackers by asking for networks that you specified in the SSID list. It's unlikely you will see any impact by this attack with your home network.
1*DSTIKE DEAUTHER WATCH SE
We Also Recommend
W1209 12V DC Digital Temperature Controller Module (Pack of 4)
Battery Level Meter & Digital Voltmeter DC 5-30V 2-Wire Battery Level Indicator & Small Battery Capacity Tester (Pack of 2)
3pcs NRF24L01+PA+LNA Wireless Transceiver RF Transceiver Module
Raspberry Pi 4B Camera with Holder and Cable IR Camera Module 75 Degree 5MP